ным образом, устанавлива в нижней его части долото или нанравл ющую башмачную пробку, затем 10-15 м УБТ, центратор , стабилизатор или калибратор разлР1Чной конструкцни, далее ой ть УБТ, так чтобы обш,а длина компановки не была больше рассто ни от забо скважины до начала нрорабатываемого интервала ствола скважины. Над этой компановкой устанавливают цилиндрический герметичный шарнир или вертлюг, затем расширитель и далее обычные бурильные трубы, собранные в свечи.In this way, the drill bit is installed in the lower part of the chisel or nanovravayuyu stopper, then 10-15 m UBT, centralizer, stabilizer or calibrator razlR1CHnoy design, then UBT, so that the general, and the length of the assembly is not more than the distance from the bottom of the well before the start of the wellbore interval. A cylindrical hermetic hinge or swivel is installed above this line-up, then a reamer and then ordinary drill pipes assembled into candles.
Бурильный инструмент, собранный в указанной носледовательности, спускают в скважину так, чтобы расширитель оказалс ниже прорабатываемого интервала ствола скважины. В этом положении восстанавливают циркул цию бурового раствора, привод т расширитель во вращение (с номощью забойного двигател или ротором через колонну бурильных труб) и поднимают его вверх на первой или второй скорости лебедки. При этом, кроме расширител , вращаютс только бурильные трубы, расположенные над ним (в случае вращени инструмента ротором). Часть бурильной колонны, наход ща с ниже расширител и цилиндрического шарнира, движетс вверх без вращени , поскольку шарнир исключает передачу крут щего момента и тем самым исключает вращение инструмента в этом поперечном сеченни. Поскольку силы сонротивлени перемещению вдоль оси скважины невращающейс колонны труб больще, чем вращающейс , нат жение участка бурильной колонны, расположенного ниже расширител , увеличиваетс , а следовательно, увеличиваютс такжеThe drilling tool, assembled in the above sequence, is lowered into the well so that the reamer is below the wellbore interval being worked. In this position, the circulation of drilling mud is restored, the expander is rotated (with the aid of a downhole motor or a rotor through a string of drill pipes) and is lifted upwards at the first or second speed of the winch. In this case, besides the reamer, only the drill pipes located above it (in the case of the tool rotating by the rotor) rotate. The part of the drill string, located below the reamer and the cylindrical hinge, moves upward without rotation, because the hinge eliminates the transmission of torque and thereby eliminates the rotation of the tool in this cross section. As the forces of resistivity for moving along the axis of a borehole of a non-rotating tubing string are larger than a rotating one, the tension of the section of the drill string located below the expander increases, and consequently also increases.
силы, прижимающие расширитель к стенкам скважины, глубина врезаии его в породу , эффективность разрушени последней и процесса проработки в целом. Кроме того, поскольку нижн часть инструмента не вращаетс , полностью исключаетс опасность отворота ее от верхней частн, надежность процесса проработки ствола скважины новышаетс , а износ бурильной колонны на участке, расноложенном ниже расширител , будет существенно меньще.the forces pressing the expander to the walls of the well, the depth of its penetration into the rock, the efficiency of destruction of the latter and the development process as a whole. In addition, since the lower part of the tool does not rotate, the danger of folding it away from the upper part is completely eliminated, the reliability of the wellbore development process is increased, and the drill string wear in the area below the reamer will be significantly less.