Claims (1)
Способ управления перемещениями, осадками и креном сооружения фундаментами колонн на сваях, объединенными ростверками, жестко соединенными с колоннами, отличающийся тем, что ветви колонны выполняют из овальных в сечение труб, опирают и закрепляют на независимых друг от друга ростверках ветвей, объединяющих сваи под ними, устанавливают по шаблону пространственные арматурные каркасы и опалубку ростверка-стопора, объединяющего сваи под ним, и являющегося макрорегулятором, и бетонируют его, причем верхняя поверхность его выступает выше поверхности пола на 600...700 мм, устанавливают на ростверк-стопор симметрично относительно вертикальной оси колонны столбики-стопоры, устанавливают по шаблону пространственные арматурные каркасы и анкерные болты, закрепленные на них, и опалубку ростверков ветвей, причем верхняя поверхность их совпадает с поверхностью пола, контролируют правильность установки анкерных болтов, навинчивают на анкерные болты нижние рихтующие гайки, контролируют отметку их верхней грани нивелиром, безвыверочно монтируют колонну, совмещая отверстия в ее базе с анкерными болтами, опускают колонну до упора ее плиты в рихтующие гайки и закрепляют базу колонны крепежными гайками, а в случае возникновения неравномерных осадок колонн, и крена колонн, определяют нивелировкой величину осадок и крена каждой колонны, устанавливают сверхнормативные отклонения осадок отдельных колонн, составляют таблицу величин необходимой стимуляции осадок колонн, получивших минимальную осадку и, исказивших прямолинейность рельсовых путей кранов и их проектные отметки, вызвавших неблагоприятные напряжения в каркасе здания, и для выравнивания осадок всех колонн, монтируют домкратную балку, соединяющую ветви, устанавливают под домкратной балкой на ростверк-стопор, домкраты-пульсаторы, с пульта управления включают домкраты-пульсаторы, в соответствие с планом выравнивания осадок колонн, полностью разгружают ростверки ветвей колонны, вдавливают ростверк-стопор в грунтовое основание, вместе с соединенными с ним сваями на проектную величину ΔSдоп, соответствующую необходимой дополнительной осадке этой колонны, контролируя величину вдавливания по лазерному нивелиру, и повышают этим несущую способность грунтового основания, разгружают домкраты-пульсаторы, и этим полностью разгружают ростверк-стопор, передают всю вертикальную сжимающую силу колонны только на ростверки ее ветвей, этим вызывают автоматическую дополнительную осадку их и колонны на величину ΔSдоп до упора домкратной балки, в столбики-стопоры, повышают этим несущую способность грунтового основания, и закрытием зазора ΔSдоп автоматически стопорят осадку колонны при достижении ей проектной отметки, затем циклы повторяют с другими колоннами.
A method of controlling the movements, precipitation and roll of the construction of the foundations of columns on piles, connected by grillages, rigidly connected to the columns, characterized in that the branches of the column are made of oval pipes into a section, are supported and fixed on independent from each other grillages of branches connecting the piles under them, spatial reinforcing cages and formwork of the grillage-stopper, uniting the piles beneath it, and which is a macroregulator, are installed according to the template, and it is concreted, and its upper surface projects higher the surface of the floor is 600 ... 700 mm, installed on the grill stopper symmetrically with respect to the vertical axis of the column, the stop columns, spatial reinforcing cages and anchor bolts mounted on them, and the formwork of the grillages of branches are installed according to the pattern, and their upper surface coincides with the surface floors, control the correct installation of the anchor bolts, screw the lower straightening nuts onto the anchor bolts, control the mark of their upper face with a level, mount the column without alignment, combining the holes in its base with with anchor bolts, lower the column to the abutment of the plate in the straightening nuts and fix the base of the column with fixing nuts, and in case of uneven column sediments, and the roll of columns, level the sediment and roll of each column by leveling, establish excess deviations of the precipitation of individual columns, compile a table of values necessary stimulation of the sediment of columns that received minimal draft and distorted the straightness of the rail tracks of the cranes and their design marks that caused adverse stresses in the frame buildings, and for leveling the sediment of all columns, they install a jack beam connecting the branches, install under the jack beam on the grill stopper, pulsating jacks, include pulsating jacks from the control panel, in accordance with the plan for aligning the sediment of the columns, completely unload the grillages of the column branches , grillage pressed-in stopper subgrade, together with connected thereto piles on a designed value ΔS additional corresponding to the desired additional precipitate the column, by controlling the magnitude of the indentation hole polar levels, and increase this bearing capacity of foundation soil discharge the jacks, pulsators, and thus completely discharge the grillage-stopper transmitting all vertical columns of compressive force only gratings its branches, this causes automatic additional precipitate them column by an amount ΔS additional to the stop jacking beams, in bars, stoppers increase the bearing capacity of this earth foundation, and closing the gap ΔS additional automatically immobilized column precipitate upon reaching it the design level, and then repeated cycles other columns.